Hello, is there any update here? Is this possible to do in new version of RD works? If so I will upgrade.
I understand it can be done in other tools, but it's a hassle to do all the time for such a simple operation.
Search found 18 matches
- Wed Apr 03, 2019 9:56 pm
- Forum: Thunder Laser Tech support
- Topic: Rounded Rectangle --- 20160101
- Replies: 3
- Views: 16903
- Wed Aug 17, 2016 4:30 am
- Forum: Thunder Laser Tech support
- Topic: Starting Location
- Replies: 2
- Views: 3402
Re: Starting Location
I downloaded the version on the website, deleted the old version and installed the new version. But both versions were the same, so I effectively just re-installed the current version. The problem is fixed. But I don't understand why a re-install was needed to fix this problem. Do you understand why...
- Wed Aug 17, 2016 1:43 am
- Forum: Thunder Laser Tech support
- Topic: Starting Location
- Replies: 2
- Views: 3402
Starting Location
Hi, I have a problem that has just started and I cannot figure out. No matter what I do, a cut that is shown will only occur at the absolute location. So, if I have a rectangle in RDWorks that goes from 300,300 to 330, 330, then when I press the "Start" button, the laser always goes to 300...
- Tue Aug 16, 2016 3:24 am
- Forum: Thunder Laser Tech support
- Topic: Size wrong
- Replies: 3
- Views: 3416
Re: Size wrong
How do I know my password for vendor settings?
- Tue Aug 16, 2016 1:59 am
- Forum: Thunder Laser Tech support
- Topic: Size wrong
- Replies: 3
- Views: 3416
Size wrong
I am cutting a part that is 177mm wide, but when it comes out, it's about 176.3mm. Some of this is kerf (about 0.2mm diameter). But even if I account for kerf, the cut size is still off.
How can I specify the steps/mm of the system?
Thanks
How can I specify the steps/mm of the system?
Thanks
- Fri Mar 25, 2016 9:48 pm
- Forum: Thunder Laser Tech support
- Topic: Mars90+ ZAxis Binding --- 20160108
- Replies: 8
- Views: 6782
Re: Mars90+ ZAxis Binding --- 20160108
The table Z Axis control is running very smoothly now. Thanks for your help.
- Wed Feb 17, 2016 7:24 am
- Forum: Thunder Laser Tech support
- Topic: Mars90+ ZAxis Binding --- 20160108
- Replies: 8
- Views: 6782
Re: Mars90+ ZAxis Binding --- 20160108
I am willing to try. I am assuming you will send board and wiring diagram and I can install myself is that right? Or do I need to send machine back? If so, it is impossible at this point.
- Tue Feb 16, 2016 4:39 pm
- Forum: Thunder Laser Tech support
- Topic: Mars90+ ZAxis Binding --- 20160108
- Replies: 8
- Views: 6782
Re: Mars90+ ZAxis Binding --- 20160108
Are you certain this will not damage the table? While using autofocus this weekend, the table became very uneven: The left side was 20mm lower than the right side, and then it made a loud noise and stopped. I could manually move it to be even again afterwards. I do not think autofocus is usable if t...
- Fri Jan 08, 2016 6:10 am
- Forum: Thunder Laser Tech support
- Topic: Mars90+ ZAxis Binding --- 20160108
- Replies: 8
- Views: 6782
Mars90+ ZAxis Binding --- 20160108
My Mars90+ seems to have an issue when adjusting the Z axis in that it binds and sounds like it's really struggling and then the z axis movement slows. As I release the Z axis button and give a tiny movement the other direction and then back in the normal direction, it seems to run smoothly again. L...
- Fri Jan 01, 2016 4:33 am
- Forum: Thunder Laser Tech support
- Topic: Rounded Rectangle --- 20160101
- Replies: 3
- Views: 16903
Rounded Rectangle --- 20160101
I understand how to create rectangle in RD. Is there a way to specify a rectangle with rounded corners? This would be very useful.