Welcome to laserengraverforum.com!

Search found 62 matches

by Ben
Mon Nov 13, 2017 6:58 am
Forum: Thunder Laser Tech support
Topic: Engraving quality problem on X-Axis
Replies: 5
Views: 472

Re: Engraving quality problem on X-Axis

Hi Stefan, Sorry for my late reply. I have tested in our NOVA35-80watt machine. It will happen when the power is much higher or the interval is much bigger. For X-unilateralism,500mm/s,25 power and interval 0.08 can engrave good on plywood. If you have more power,the wood will produce more wood chip...
by Ben
Mon Oct 30, 2017 1:27 am
Forum: Thunder Laser Tech support
Topic: Engraving quality problem on X-Axis
Replies: 5
Views: 472

Re: Engraving quality problem on X-Axis

Hi Stefan,

Since the Y axis direction have two rails,it can be more fixed while engraving with Y-swing.
I'd like to know how is the result of X-unilaterism,thanks.
by Ben
Sat Oct 28, 2017 6:45 am
Forum: General Laser machine discussion
Topic: Thunderlaser Nova 63 and big item
Replies: 5
Views: 1652

Re: Thunderlaser Nova 63 and big item

Hi Tumim,

I'm not sure what you want,it would be better to show me some pictures,thanks.
by Ben
Fri Oct 27, 2017 2:29 am
Forum: General Laser machine discussion
Topic: Thunderlaser Nova 63 and big item
Replies: 5
Views: 1652

Re: Thunderlaser Nova 63 and big item

Hi Tumim, Yes,you can press "origin" to set the start point according to the red dot indicator,and press "Frame" to confirm the processing area,so you can cut it right. cutting two pieces in a time cannot get a better result,there will be much burnt between two pieces and easy to cause the misalignm...
by Ben
Fri Sep 22, 2017 9:23 am
Forum: Thunder Laser Tech support
Topic: Cutting Problem
Replies: 12
Views: 1379

Re: Cutting Problem

Hi Steven, There is a solution for you. You can use the laser through mode,set the Open Delay,then the machine will laser on the Through power during the Open Delay time without laser head movement. laser head will move with the working power until the Open Delay time is up. Set back the TL-timer to...
by Ben
Fri Sep 22, 2017 1:43 am
Forum: Thunder Laser Tech support
Topic: Cutting Problem
Replies: 12
Views: 1379

Re: Cutting Problem

Hi Steven, The amp circuit is determined by the machine loading. It's enough for the start up. I think that the problem should not happen from the very beginning. And yes,there is some sort of power problem with the laser when the laser, air compress and the blower come on at the same time. But even...
by Ben
Tue Sep 19, 2017 9:36 am
Forum: Thunder Laser Tech support
Topic: Cutting Problem
Replies: 12
Views: 1379

Re: Cutting Problem

TL-Timer-51.jpg
TL-Timer-51.jpg (804.96 KiB) Viewed 650 times
by Ben
Mon Sep 18, 2017 2:21 am
Forum: Thunder Laser Tech support
Topic: Cutting Problem
Replies: 12
Views: 1379

Re: Cutting Problem

Hi Steven, Thanks for your information. So only blower be plugged to the outlet of the exhaust fan,the problem happens,right? Blower and air compressor,they both connect to the TL-timer,please try the "MANUAL" mode of TL-timer. Then try again with the test. http://www.thunderlaser.com/features/smart...
by Ben
Thu Sep 14, 2017 6:54 am
Forum: Thunder Laser Tech support
Topic: Cutting Problem
Replies: 12
Views: 1379

Re: Cutting Problem

Hi Steven, Good to hear from you. Haha,we have also encountered several typhoon these two months in Guangdong province. For your cutting problem,can you show some pictures to explain the problem,i'm not quite sure what you mean for the first 3/8" doesn't cut through. If the laser just doesn't have e...
by Ben
Thu Sep 14, 2017 6:36 am
Forum: Thunder Laser Tech support
Topic: cutting heat transfer vinyl
Replies: 1
Views: 350

Re: cutting heat transfer vinyl

please send us the links for cutting HTV.