Search found 24 matches

by stevenresnick
Sun Jun 24, 2018 2:12 pm
Forum: Thunder Laser Tech support
Topic: Laser Tube Replacement
Replies: 1
Views: 172

Laser Tube Replacement

I need to replace my tube in a Nova 34 100 watt and would like to replace it with a
RECI W4 100 watt tube?
Will this work or do I need to replace it with the same tube that came with the laser.

Thanks,
Steven
by stevenresnick
Tue Jun 19, 2018 6:54 am
Forum: Thunder Laser Tech support
Topic: Loss of Power!!!!
Replies: 3
Views: 329

Re: Loss of Power!!!!

Does it matter what brand I replace it with????
by stevenresnick
Mon Jun 18, 2018 12:21 am
Forum: Thunder Laser Tech support
Topic: Loss of Power!!!!
Replies: 3
Views: 329

Loss of Power!!!!

Today my laser stop cutting through 6mm Birch Plywood and 6mm MDF. I've check the alignment of all the mirrors and that's all perfect and Clean. I also pulsed into the 10mm acrylic and that was perfectly straight. I also checked the power supply and pressed the test button and got the green light. ...
by stevenresnick
Tue May 29, 2018 8:52 pm
Forum: Thunder Laser Tech support
Topic: Not Engraving in the absolute position
Replies: 5
Views: 464

Re: Not Engraving in the absolute position

Ben,
I just tried another test......
When I have a shape (square) and place it in an absolute position it cuts it out exactly where I placed it, but if I put another square inside of it to engrave it doesn't line up. Like in the original photo.

Thanks,
Steven
by stevenresnick
Tue May 29, 2018 7:35 pm
Forum: Thunder Laser Tech support
Topic: Not Engraving in the absolute position
Replies: 5
Views: 464

Re: Not Engraving in the absolute position

Hi Ben,
I went a head and tried what you suggested and it didn't change at all.

Please advise what you think I should do next.

Thanks
Steven
by stevenresnick
Tue May 29, 2018 9:29 am
Forum: Thunder Laser Tech support
Topic: Not Engraving in the absolute position
Replies: 5
Views: 464

Re: Not Engraving in the absolute position

Hi Ben,
Thanks for the res response.
How do I clear the memory of the controller??

What happens when I format the controller?
Will i have to enter any info or settings?

I a wait your response before I make any changes

Thanks
Steven
by stevenresnick
Mon May 28, 2018 5:01 pm
Forum: Thunder Laser Tech support
Topic: Not Engraving in the absolute position
Replies: 5
Views: 464

Not Engraving in the absolute position

Can someone tell me why the part that I'm engraving into is off center by 1/8".
Please the attached photo.
The X is whats off
For some reason the photo rotated.

Thanks
Steven


Nova 35 100 Watt
RDW V8.01.18
by stevenresnick
Sun Apr 15, 2018 4:59 pm
Forum: Laser softwares for Chinese manufacturers
Topic: RDWorks Version
Replies: 1
Views: 493

RDWorks Version

Can someone tell me what the latest version of RDWorks is and were can I download it from???

ThunderLaser Nova 35

Thanks,
Steven
by stevenresnick
Tue Sep 26, 2017 12:28 am
Forum: Thunder Laser Tech support
Topic: Cutting Problem
Replies: 12
Views: 3985

Re: Cutting Problem

Hi Ben
I tried what you had recommended and the results are the
same.
It works fine when in the manual mode.
Could a part gone bad???

Thanks
Steven
by stevenresnick
Tue Sep 19, 2017 12:45 pm
Forum: Thunder Laser Tech support
Topic: Cutting Problem
Replies: 12
Views: 3985

Re: Cutting Problem

Hi Ben That worked, but the blower will run as soon as I power up the laser. Is there any other solutions so the blower comes on when the laser starts? What is the total amps for the Laser, compressor and blower?? The laser is plugged into a 20 amp circuit. That may not be enough for the start up. T...