Search found 25 matches

by stevenresnick
Sun Aug 25, 2019 3:29 pm
Forum: Thunder Laser Tech support
Topic: Weak Laser Tube
Replies: 1
Views: 8647

Weak Laser Tube

Its seams after the laser runs for about 30 min the power drops and the engraved area isn't engraving as deep as when I first started 30 minutes prior. If I let the laser set overnight and start over again I have the same problem. Could I have a bad tube??? I replaced the tube one year ago. Thanks S...
by stevenresnick
Sun Jun 24, 2018 2:12 pm
Forum: Thunder Laser Tech support
Topic: Laser Tube Replacement
Replies: 1
Views: 7773

Laser Tube Replacement

I need to replace my tube in a Nova 34 100 watt and would like to replace it with a
RECI W4 100 watt tube?
Will this work or do I need to replace it with the same tube that came with the laser.

Thanks,
Steven
by stevenresnick
Tue Jun 19, 2018 6:54 am
Forum: Thunder Laser Tech support
Topic: Loss of Power!!!!
Replies: 3
Views: 11218

Re: Loss of Power!!!!

Does it matter what brand I replace it with????
by stevenresnick
Mon Jun 18, 2018 12:21 am
Forum: Thunder Laser Tech support
Topic: Loss of Power!!!!
Replies: 3
Views: 11218

Loss of Power!!!!

Today my laser stop cutting through 6mm Birch Plywood and 6mm MDF. I've check the alignment of all the mirrors and that's all perfect and Clean. I also pulsed into the 10mm acrylic and that was perfectly straight. I also checked the power supply and pressed the test button and got the green light. ...
by stevenresnick
Tue May 29, 2018 8:52 pm
Forum: Thunder Laser Tech support
Topic: Not Engraving in the absolute position
Replies: 5
Views: 11226

Re: Not Engraving in the absolute position

Ben,
I just tried another test......
When I have a shape (square) and place it in an absolute position it cuts it out exactly where I placed it, but if I put another square inside of it to engrave it doesn't line up. Like in the original photo.

Thanks,
Steven
by stevenresnick
Tue May 29, 2018 7:35 pm
Forum: Thunder Laser Tech support
Topic: Not Engraving in the absolute position
Replies: 5
Views: 11226

Re: Not Engraving in the absolute position

Hi Ben,
I went a head and tried what you suggested and it didn't change at all.

Please advise what you think I should do next.

Thanks
Steven
by stevenresnick
Tue May 29, 2018 9:29 am
Forum: Thunder Laser Tech support
Topic: Not Engraving in the absolute position
Replies: 5
Views: 11226

Re: Not Engraving in the absolute position

Hi Ben,
Thanks for the res response.
How do I clear the memory of the controller??

What happens when I format the controller?
Will i have to enter any info or settings?

I a wait your response before I make any changes

Thanks
Steven
by stevenresnick
Mon May 28, 2018 5:01 pm
Forum: Thunder Laser Tech support
Topic: Not Engraving in the absolute position
Replies: 5
Views: 11226

Not Engraving in the absolute position

Can someone tell me why the part that I'm engraving into is off center by 1/8".
Please the attached photo.
The X is whats off
For some reason the photo rotated.

Thanks
Steven


Nova 35 100 Watt
RDW V8.01.18
by stevenresnick
Sun Apr 15, 2018 4:59 pm
Forum: Laser softwares for Chinese manufacturers
Topic: RDWorks Version
Replies: 1
Views: 3970

RDWorks Version

Can someone tell me what the latest version of RDWorks is and were can I download it from???

ThunderLaser Nova 35

Thanks,
Steven
by stevenresnick
Tue Sep 26, 2017 12:28 am
Forum: Thunder Laser Tech support
Topic: Cutting Problem
Replies: 12
Views: 8155

Re: Cutting Problem

Hi Ben
I tried what you had recommended and the results are the
same.
It works fine when in the manual mode.
Could a part gone bad???

Thanks
Steven