Search found 25 matches
- Sun Aug 25, 2019 3:29 pm
- Forum: Thunder Laser Tech support
- Topic: Weak Laser Tube
- Replies: 1
- Views: 13692
Weak Laser Tube
Its seams after the laser runs for about 30 min the power drops and the engraved area isn't engraving as deep as when I first started 30 minutes prior. If I let the laser set overnight and start over again I have the same problem. Could I have a bad tube??? I replaced the tube one year ago. Thanks S...
- Sun Jun 24, 2018 2:12 pm
- Forum: Thunder Laser Tech support
- Topic: Laser Tube Replacement
- Replies: 1
- Views: 12929
Laser Tube Replacement
I need to replace my tube in a Nova 34 100 watt and would like to replace it with a
RECI W4 100 watt tube?
Will this work or do I need to replace it with the same tube that came with the laser.
Thanks,
Steven
RECI W4 100 watt tube?
Will this work or do I need to replace it with the same tube that came with the laser.
Thanks,
Steven
- Tue Jun 19, 2018 6:54 am
- Forum: Thunder Laser Tech support
- Topic: Loss of Power!!!!
- Replies: 3
- Views: 17064
Re: Loss of Power!!!!
Does it matter what brand I replace it with????
- Mon Jun 18, 2018 12:21 am
- Forum: Thunder Laser Tech support
- Topic: Loss of Power!!!!
- Replies: 3
- Views: 17064
Loss of Power!!!!
Today my laser stop cutting through 6mm Birch Plywood and 6mm MDF. I've check the alignment of all the mirrors and that's all perfect and Clean. I also pulsed into the 10mm acrylic and that was perfectly straight. I also checked the power supply and pressed the test button and got the green light. ...
- Tue May 29, 2018 8:52 pm
- Forum: Thunder Laser Tech support
- Topic: Not Engraving in the absolute position
- Replies: 5
- Views: 17719
Re: Not Engraving in the absolute position
Ben,
I just tried another test......
When I have a shape (square) and place it in an absolute position it cuts it out exactly where I placed it, but if I put another square inside of it to engrave it doesn't line up. Like in the original photo.
Thanks,
Steven
I just tried another test......
When I have a shape (square) and place it in an absolute position it cuts it out exactly where I placed it, but if I put another square inside of it to engrave it doesn't line up. Like in the original photo.
Thanks,
Steven
- Tue May 29, 2018 7:35 pm
- Forum: Thunder Laser Tech support
- Topic: Not Engraving in the absolute position
- Replies: 5
- Views: 17719
Re: Not Engraving in the absolute position
Hi Ben,
I went a head and tried what you suggested and it didn't change at all.
Please advise what you think I should do next.
Thanks
Steven
I went a head and tried what you suggested and it didn't change at all.
Please advise what you think I should do next.
Thanks
Steven
- Tue May 29, 2018 9:29 am
- Forum: Thunder Laser Tech support
- Topic: Not Engraving in the absolute position
- Replies: 5
- Views: 17719
Re: Not Engraving in the absolute position
Hi Ben,
Thanks for the res response.
How do I clear the memory of the controller??
What happens when I format the controller?
Will i have to enter any info or settings?
I a wait your response before I make any changes
Thanks
Steven
Thanks for the res response.
How do I clear the memory of the controller??
What happens when I format the controller?
Will i have to enter any info or settings?
I a wait your response before I make any changes
Thanks
Steven
- Mon May 28, 2018 5:01 pm
- Forum: Thunder Laser Tech support
- Topic: Not Engraving in the absolute position
- Replies: 5
- Views: 17719
Not Engraving in the absolute position
Can someone tell me why the part that I'm engraving into is off center by 1/8".
Please the attached photo.
The X is whats off
For some reason the photo rotated.
Thanks
Steven
Nova 35 100 Watt
RDW V8.01.18
Please the attached photo.
The X is whats off
For some reason the photo rotated.
Thanks
Steven
Nova 35 100 Watt
RDW V8.01.18
- Sun Apr 15, 2018 4:59 pm
- Forum: Laser softwares for Chinese manufacturers
- Topic: RDWorks Version
- Replies: 1
- Views: 4588
RDWorks Version
Can someone tell me what the latest version of RDWorks is and were can I download it from???
ThunderLaser Nova 35
Thanks,
Steven
ThunderLaser Nova 35
Thanks,
Steven
- Tue Sep 26, 2017 12:28 am
- Forum: Thunder Laser Tech support
- Topic: Cutting Problem
- Replies: 12
- Views: 9452
Re: Cutting Problem
Hi Ben
I tried what you had recommended and the results are the
same.
It works fine when in the manual mode.
Could a part gone bad???
Thanks
Steven
I tried what you had recommended and the results are the
same.
It works fine when in the manual mode.
Could a part gone bad???
Thanks
Steven