Search found 115 matches
- Tue May 10, 2016 8:31 am
- Forum: Thunder Laser Tech support
- Topic: Cutting Acrylic sheet --- 20160515
- Replies: 6
- Views: 5812
Re: Cutting Acrylic sheet
1. thank you for your photos i understood what you mention now so i think that the issue should be the focus distance, please check if you set that right with the focus Please make it sure the focus must be 6mm from the bottom of head to the surface of material If not, please try to find out what is...
- Mon May 09, 2016 1:45 am
- Forum: Thunder Laser Tech support
- Topic: Cutting Acrylic sheet --- 20160515
- Replies: 6
- Views: 5812
Re: Cutting Acrylic sheet
Hi Young Sorry reply you so lately cause we were out in the weekend For your questions 1. Could you please take a picture about the cutting result to show me and also sending your file to me for checking It's just a drawing graphics, a real cutting result will provide me more details 2. align the la...
- Tue May 03, 2016 1:01 pm
- Forum: Thunder Laser Tech support
- Topic: Variable Power?
- Replies: 3
- Views: 4246
Re: Variable Power?
Hi Chris If your BMP image is a grayscale image? If yeah, please select that output direct option in layer for engraving 2.5D grayscale image I don't know what engraving result are you want? the engraving area is shallow or deep? do you need 2.5D engraving result? If your BMP is 300 DPI, please set ...
- Tue May 03, 2016 2:13 am
- Forum: Thunder Laser Tech support
- Topic: Variable Power?
- Replies: 3
- Views: 4246
Re: Variable Power?
Hi Chris No need to create another layer with a different power setting, of course, your file is a BMP file, You would not create another layer for it If your BMP layer based on shades of grey, please set that min power to 15% and the max power to 30% even higher, Let both power settings are differe...
- Thu Apr 14, 2016 1:07 am
- Forum: Thunder Laser Tech support
- Topic: Rotary Attachment does not turn
- Replies: 3
- Views: 4800
Re: Rotary Attachment does not turn
Hi Steve for point 6 to answer If you connected it to x-axis by made a new cable to run from white controller directly And it does not work, it proves the motor is fail And yeah, you said right, when power is on, motor is resistant to running, we almost cannot move it by hand if it works fine But no...
- Tue Apr 12, 2016 7:05 am
- Forum: Thunder Laser Tech support
- Topic: Rotary Attachment does not turn
- Replies: 3
- Views: 4800
Re: Rotary Attachment does not turn
Hi Steve 1. all the connector are good 2. connection also good too 3. 36V power input are good 4. what about the signal from the white main controller to the rotary motor? this is very important. 5. the main controller should be ok, because when the laser controls the y-axis to move, it works, right...
- Mon Apr 04, 2016 10:54 am
- Forum: Thunder Laser Tech support
- Topic: Mars90_Z axis movement problem.
- Replies: 3
- Views: 4274
Re: Mars90_Z axis movement problem.
Hi Joon This is Tom from thunder laser Sorry reply so lately cause we are on holiday these days Thank you for your carefully checking And let me try to give you a solution Yeah, i know you did not used the auto focus and also the sensor may not dirty at all But it was activated even if its under has...
- Mon Apr 04, 2016 10:46 am
- Forum: Thunder Laser Tech support
- Topic: Mars90+ ZAxis Binding --- 20160108
- Replies: 8
- Views: 6782
Re: Mars90+ ZAxis Binding --- 20160108
Hi Matthew
Sorry has no response so lately
So you connected the driver for z-axis by yourself
And then the z-axis table is running smoothly
You refer to the other one driver of z-axis to connected with this new driver, right? good
Hope you everything is ok
Having a nice day
Sorry has no response so lately
So you connected the driver for z-axis by yourself
And then the z-axis table is running smoothly
You refer to the other one driver of z-axis to connected with this new driver, right? good
Hope you everything is ok
Having a nice day
- Tue Mar 22, 2016 2:06 pm
- Forum: Thunder Laser Tech support
- Topic: Cannot start cutting with RD Vision---20160309
- Replies: 7
- Views: 5067
Re: Cannot start cutting with RD Vision---20160309
Hi Andy You said that you gave the correct cross position to start? And you used the splicing model to cut your simple inported DXF outline? You meant that you selected the cross as the features? then used two marks as the feature? Then do you selected a correct feature with your spliced picture? If...
- Mon Mar 14, 2016 4:27 am
- Forum: Thunder Laser Tech support
- Topic: Incrementing numbers using scan x_ unilateralism--20160314
- Replies: 1
- Views: 3192
Re: Incrementing numbers using scan x_ unilateralism--20160314
Hi Henk Sorry to reply so lately For your questions 1. do you know how to set up a series of number to engrave then cut out on each plate? and positioning the number in the middle of each plates? see below picture to know how to do that, but you need to set it up one by one 2. how to making one plat...