Search found 84 matches
- Sat Jan 07, 2017 1:00 am
- Forum: Thunder Laser Tech support
- Topic: My mars90 machine need some help!
- Replies: 4
- Views: 5572
Re: My mars90 machine need some help!
Hi Peter, your problem should be caused by the table that it wasn't level both sides. First Checking. 31.jpg Ok, let's us to fix it out You know, the table was controlled by two motor under the table, you should looked them before And the reason as you said that the motors are a little out of sync P...
- Fri Jan 06, 2017 6:59 am
- Forum: Thunder Laser Tech support
- Topic: My mars90 machine need some help!
- Replies: 4
- Views: 5572
Re: My mars90 machine need some help!
Hi Peter, your computer can not communicate with the machine,right? Okay, it should be a driver issue. i think that you did not installed the driver finished for your pc So the software still does not recognize the machine. I believe that you should tried installing the driver for pc using automatic...
- Sat Dec 31, 2016 6:58 am
- Forum: Laser softwares for Chinese manufacturers
- Topic: Has anyone seen this when performing laser alignment?
- Replies: 5
- Views: 4093
Re: Has anyone seen this when performing laser alignment?
From your picture, the laser beam size is big, can you please try to cut 10mm acrylic with 70% power, and tell us what is the highest speed?
- Fri Dec 30, 2016 3:02 pm
- Forum: General Laser machine discussion
- Topic: Interlock switch
- Replies: 1
- Views: 1387
Re: Interlock switch
Hi,
You can search "Keylock Selector Select Switch" on Amazon or Ebay,such as
https://www.amazon.com/dp/B009IPEB8A
https://www.amazon.com/dp/B008ZY9CXE
However ,our Thunderlaser machine to improve the reliability of machine safety, the plane has dual key lock and electrical safety
You can search "Keylock Selector Select Switch" on Amazon or Ebay,such as
https://www.amazon.com/dp/B009IPEB8A
https://www.amazon.com/dp/B008ZY9CXE
However ,our Thunderlaser machine to improve the reliability of machine safety, the plane has dual key lock and electrical safety
- Wed Dec 28, 2016 12:59 am
- Forum: Thunder Laser Tech support
- Topic: My mars90 machine need some help!
- Replies: 4
- Views: 5572
Re: My mars90 machine need some help!
Hi Peter, 1. As you purchased the laser about 4~5 years ago, the software should be lasergrave. As we use another controller and software, but you still can download lasergrave from this link. http://www.thunderlaser.com/download/down/LaserGRAV_V8.98.exe 2. Not sure your laser is good or not, you do...
- Mon Dec 26, 2016 7:27 am
- Forum: Laser Knowledge
- Topic: Laser Engraver
- Replies: 2
- Views: 3400
Re: Laser Engraver
Hi Sir or Madam, I am yumiko from thunderlaser,may I know how thick for your poly carbonate are you going to cut? and may I know where are you from? for poly carbonate,engraving by laser machine is no problem,however,cutting is not good. As we have client from Australia by our machine do this materi...
- Mon Dec 26, 2016 7:26 am
- Forum: General Laser machine discussion
- Topic: Laser problem
- Replies: 2
- Views: 2002
Re: Laser problem
Hi!
Thanks for your video.
First of all, I need to check the vendor setting of your laser.
please kindly find attached picture and show me picture as it shown.
Thanks for your video.
First of all, I need to check the vendor setting of your laser.
please kindly find attached picture and show me picture as it shown.
- Mon Dec 19, 2016 3:56 am
- Forum: Thunder Laser Tech support
- Topic: Files can not be imported into PHCAD software
- Replies: 3
- Views: 3908
Re: Files can not be imported into PHCAD software
Hi David, If the dxf file i sent to you can run by PHCAD. 1、why The PHCAD software does not recognise a simple .ai file produced from a commercial version of Adobe Illustrator even though it says it can. The PHCAD have not optimized since 2013,so lead to it can not support high version of ai file we...
- Wed Dec 14, 2016 5:59 am
- Forum: Thunder Laser Tech support
- Topic: Files can not be imported into PHCAD software
- Replies: 3
- Views: 3908
Re: Files can not be imported into PHCAD software
Hi David, I had tried the file you attached,and all files except .dxf file have error. Maybe you did not convert this file in correct way. I have had tried to convert the file as .dxf file and it can be imported by PHCAD. What type the file save as,please see the attached picture. and also send the ...
- Mon Dec 12, 2016 5:42 am
- Forum: Thunder Laser Tech support
- Topic: 3D engrave
- Replies: 12
- Views: 10149
Re: 3D engrave
Hi Jasper_Rullman
Thanks for you suggested.
it will help us to improve our software.
Hoping you everything is well.
Thanks for you suggested.
it will help us to improve our software.
Hoping you everything is well.