Hi Anda,
Installation of focus lens please refer to below picture:
Yes,you can use 4 inch head to cut,the focal distance is 10mm.
Search found 137 matches
- Thu May 03, 2018 1:14 am
- Forum: Thunder Laser Tech support
- Topic: 4 inch laser head - kind of urgent
- Replies: 2
- Views: 4329
- Thu May 03, 2018 1:07 am
- Forum: Thunder Laser Tech support
- Topic: lenses - interchangeable?
- Replies: 1
- Views: 2882
- Thu May 03, 2018 1:02 am
- Forum: Thunder Laser Tech support
- Topic: Inconsistent results when cutting material close to 10mm
- Replies: 9
- Views: 48090
Re: Inconsistent results when cutting material close to 10mm
Please first check it according to the attachment.
- Wed Apr 25, 2018 5:41 am
- Forum: Thunder Laser Tech support
- Topic: X-axis does not work anymore
- Replies: 5
- Views: 4553
Re: X-axis does not work anymore
You are welcome and good to hear that you resolved the problem.
- Wed Apr 25, 2018 3:09 am
- Forum: Laser Knowledge
- Topic: laser marking hip flask
- Replies: 1
- Views: 2494
Re: laser marking hip flask
Hi Deborah, For laser marking hip flask,actually the fiber laser marking machine is easier and better. The CO2 laser machine can also do that,you should coat the stainless steel or metal with a product called thermark spray and you laser it and it makes a permanent black mark. Works real well. I fi...
- Tue Apr 24, 2018 1:00 am
- Forum: Thunder Laser Tech support
- Topic: X-axis does not work anymore
- Replies: 5
- Views: 4553
Re: X-axis does not work anymore
Hi Joe,
If it's the problem of Y axis,please refer to troubleshooting below,
http://www.thunderlaser.com/troubleshoo ... denly.html
If it's the problem of Y axis,please refer to troubleshooting below,
http://www.thunderlaser.com/troubleshoo ... denly.html
- Mon Apr 23, 2018 9:51 am
- Forum: Thunder Laser Tech support
- Topic: Nova 63 - red dot pointer / xy axis/ water-oil separator
- Replies: 4
- Views: 3170
Re: Nova 63 - red dot pointer / xy axis/ water-oil separator
Hi Anda, #2. Ok,i got it. Actually,the laser head is working well on 1600*1000 mm working area. But why the laser head will go beyond a little bit from the honeycomb table,because we fasten the honeycomb table on the machine with two Plug-pin,see below. QQ图片20170622141942.jpg QQ图片20170622141938.jpg ...
- Mon Apr 23, 2018 7:53 am
- Forum: Thunder Laser Tech support
- Topic: Nova 63 - red dot pointer / xy axis/ water-oil separator
- Replies: 4
- Views: 3170
Re: Nova 63 - red dot pointer / xy axis/ water-oil separator
Hi Anda, Sorry for those problem. #1. I think the alignment of red dot should have been changed during shipping.You will need to adjust it to make the red light coming out from the laser head.How to do it please refer to the picture below. realign red dot.jpg #2. The head goes beyond the low left co...
- Sat Apr 21, 2018 9:07 am
- Forum: Thunder Laser Tech support
- Topic: X-axis does not work anymore
- Replies: 5
- Views: 4553
Re: X-axis does not work anymore
Hello Joe, Your mars 90 was brought in November 2011,it's very old machine. To answer your problem, 1.The X-aixs doesn't work anymore,did you check the X-axis driver already?see below. I wonder whether the driver be powered on or not. X-axis driver.png 2.The cable of Y-axis stepper motor goes to the...
- Fri Apr 20, 2018 2:39 am
- Forum: General Laser machine discussion
- Topic: Pulling my hair out
- Replies: 7
- Views: 8593
Re: Pulling my hair out
Hi,
If you have changed the controller.
Please note,new one have not set the vendor setting and user setting.
You should do it first to work with your machine.
If you have changed the controller.
Please note,new one have not set the vendor setting and user setting.
You should do it first to work with your machine.