Search found 137 matches
- Fri Sep 22, 2017 1:43 am
- Forum: Thunder Laser Tech support
- Topic: Cutting Problem
- Replies: 12
- Views: 8830
Re: Cutting Problem
Hi Steven, The amp circuit is determined by the machine loading. It's enough for the start up. I think that the problem should not happen from the very beginning. And yes,there is some sort of power problem with the laser when the laser, air compress and the blower come on at the same time. But even...
- Tue Sep 19, 2017 9:36 am
- Forum: Thunder Laser Tech support
- Topic: Cutting Problem
- Replies: 12
- Views: 8830
- Mon Sep 18, 2017 2:21 am
- Forum: Thunder Laser Tech support
- Topic: Cutting Problem
- Replies: 12
- Views: 8830
Re: Cutting Problem
Hi Steven, Thanks for your information. So only blower be plugged to the outlet of the exhaust fan,the problem happens,right? Blower and air compressor,they both connect to the TL-timer,please try the "MANUAL" mode of TL-timer. Then try again with the test. http://www.thunderlaser.com/feat...
- Thu Sep 14, 2017 6:54 am
- Forum: Thunder Laser Tech support
- Topic: Cutting Problem
- Replies: 12
- Views: 8830
Re: Cutting Problem
Hi Steven, Good to hear from you. Haha,we have also encountered several typhoon these two months in Guangdong province. For your cutting problem,can you show some pictures to explain the problem,i'm not quite sure what you mean for the first 3/8" doesn't cut through. If the laser just doesn't h...
- Thu Sep 14, 2017 6:36 am
- Forum: Thunder Laser Tech support
- Topic: cutting heat transfer vinyl
- Replies: 1
- Views: 2382
Re: cutting heat transfer vinyl
please send us the links for cutting HTV.
- Mon Sep 11, 2017 3:29 am
- Forum: Thunder Laser Tech support
- Topic: Cutting Problem
- Replies: 12
- Views: 8830
Re: Cutting Problem
Hi Steven,
Do you mean laser cannot cut through at the left top corner?please laser a 10mm acrylic to check if the laser beam is vertical.
About the exhaust fan, do you mean it starts after turn on the laser switch,you want it starts till you start a job,right?
Do you mean laser cannot cut through at the left top corner?please laser a 10mm acrylic to check if the laser beam is vertical.
About the exhaust fan, do you mean it starts after turn on the laser switch,you want it starts till you start a job,right?
- Mon Aug 14, 2017 1:27 am
- Forum: Thunder Laser Tech support
- Topic: CHILLER Problem
- Replies: 7
- Views: 5979
Re: CHILLER Problem
It would be good and no problem
Any problems just keep in touch.
Any problems just keep in touch.
- Wed Aug 09, 2017 2:53 am
- Forum: Thunder Laser Tech support
- Topic: CHILLER Problem
- Replies: 7
- Views: 5979
Re: CHILLER Problem
Hi Andy, Please note:you should use a water pipe directly connected to chiller water outlet and inlet before turn chiller on.see attachment From your video,it seems there is no water flowing,did you check the water,is it enough.see attachment. If water is enough but no water flowing,please open the ...
- Mon Aug 07, 2017 7:46 am
- Forum: Thunder Laser Tech support
- Topic: CHILLER Problem
- Replies: 7
- Views: 5979
Re: CHILLER Problem
Hi Andy,
OK,please turn off your chiller.
Then use a water pipe directly connected to chiller water outlet and inlet.
Check if the alarm is still on and is there water flowing?
OK,please turn off your chiller.
Then use a water pipe directly connected to chiller water outlet and inlet.
Check if the alarm is still on and is there water flowing?
- Tue Jul 18, 2017 10:06 am
- Forum: General Laser machine discussion
- Topic: Thunder Laser Mars 90 Y axis stuck
- Replies: 1
- Views: 1314
Re: Thunder Laser Mars 90 Y axis stuck
Hi Ron,
OK,the Rotary switch is off,you should have it switched to "O".
Then the Y axis can be move,but it only moves under 5 inches or so,even press the reset button the Y aixs cannot move on the full 600mm,right?
OK,the Rotary switch is off,you should have it switched to "O".
Then the Y axis can be move,but it only moves under 5 inches or so,even press the reset button the Y aixs cannot move on the full 600mm,right?