Search found 137 matches
- Tue Jun 19, 2018 2:20 am
- Forum: Thunder Laser Tech support
- Topic: Loss of Power!!!!
- Replies: 3
- Views: 16660
Re: Loss of Power!!!!
Hi Steven, It seems that the laser tube have loss of power. The ammeter have reading of 23,so the laser power supply should be fine. If the laser tube have lost power so much as you said,i'm afraid it became bad now. To check the laser tube,please check the Beam pattern of laser tube by laser a dot ...
- Sat Jun 16, 2018 8:19 am
- Forum: Thunder Laser Tech support
- Topic: X-axis does not work
- Replies: 5
- Views: 17085
Re: X-axis does not work
Hi Mariusz,
OK,the laser hear can reset to top left corner,so the connection for motor and driver should be fine.
So if the laser head can normally touch the X axis limit switch,or hit the limit switch and stop then do not move anymore.
OK,the laser hear can reset to top left corner,so the connection for motor and driver should be fine.
So if the laser head can normally touch the X axis limit switch,or hit the limit switch and stop then do not move anymore.
- Sat Jun 16, 2018 3:36 am
- Forum: Thunder Laser Tech support
- Topic: X-axis does not work
- Replies: 5
- Views: 17085
Re: X-axis does not work
Hi Mariusz,
Sorry for your problem.
About your problem,X-axis does not work,i'm wondering if the laser head can reset to top left corner when turn on the machine,or just Y axis work well.
Sorry for your problem.
About your problem,X-axis does not work,i'm wondering if the laser head can reset to top left corner when turn on the machine,or just Y axis work well.
- Wed May 30, 2018 3:29 am
- Forum: Thunder Laser Tech support
- Topic: Not Engraving in the absolute position
- Replies: 5
- Views: 17310
Re: Not Engraving in the absolute position
Hi Steven,
As you said,it's more likely about the controller or software issue.
Please send me the test files for checking.Thanks.
As you said,it's more likely about the controller or software issue.
Please send me the test files for checking.Thanks.
- Tue May 29, 2018 5:53 am
- Forum: Thunder Laser Tech support
- Topic: Not Engraving in the absolute position
- Replies: 5
- Views: 17310
Re: Not Engraving in the absolute position
Hi Steven, It seems that controller is not working well. Maybe the memory of controller is full,please clean up the files. Or you can just format the memory as following. On LCD panel>>File>>Other+>>format the memory speedily. After that,let me know if that problem is resolved or not.
- Fri May 25, 2018 2:08 am
- Forum: Thunder Laser Tech support
- Topic: Inconsistent results when cutting material close to 10mm
- Replies: 9
- Views: 47810
Re: Inconsistent results when cutting material close to 10mm
Hi Idan, If there's a lot of loss for the laser power,it's more about the problem from focus lens or laser beam path. Please check them for sure,the focus lens is intact and clean and the laser beam goes down vertically to four corner of table. If they are just fine,so it seems that the power of las...
- Wed May 23, 2018 6:08 am
- Forum: Thunder Laser Tech support
- Topic: Eye protection
- Replies: 2
- Views: 13503
Re: Eye protection
Hi Idan,
We buy the eye potection glasses on Taobao instead of Amazon.
You can refer to the link below.
https://www.cnczone.com/forums/general- ... laser.html
We buy the eye potection glasses on Taobao instead of Amazon.
You can refer to the link below.
https://www.cnczone.com/forums/general- ... laser.html
- Wed May 23, 2018 5:50 am
- Forum: Thunder Laser Tech support
- Topic: Inconsistent results when cutting material close to 10mm
- Replies: 9
- Views: 47810
Re: Inconsistent results when cutting material close to 10mm
Hi Idan, Sorry for my late reply. For your cutting problem,sometimes it cut through just fine and other times it won't. It seems that the setting is at the threshold between cut through or not. We suggest to lower the speed a little bit just fine. Besides,you should know that the MDF is more difficu...
- Tue May 15, 2018 1:27 am
- Forum: Thunder Laser Tech support
- Topic: FILE forma error RDworks 8.1
- Replies: 1
- Views: 17654
Re: FILE forma error RDworks 8.1
Please install the RDworksV8.19.
It has setting for reverse interval and good to X-swing engraving.
http://www.thunderlaser.com/download/down/RDWorksV8.rar
It has setting for reverse interval and good to X-swing engraving.
http://www.thunderlaser.com/download/down/RDWorksV8.rar
- Tue May 15, 2018 1:23 am
- Forum: Thunder Laser Tech support
- Topic: Edit startingpoint of cutting
- Replies: 1
- Views: 15506
Re: Edit startingpoint of cutting
Generally,it's left top corner.