Poor quality photo engraving

Discuss Laser Control Softwares here!

Moderator: baker

futrelis
Posts: 14
Joined: Sat Jul 22, 2017 12:56 am

Re: Poor quality photo engraving

Post by futrelis »

Iam reading this http://wiki.linuxcnc.org/cgi-bin/wiki.p ... th_A_Laser
how you can mofify linuxcnc for doing raster engraving..
closeracing
Posts: 22
Joined: Sat Jul 08, 2017 1:38 am

Re: Poor quality photo engraving

Post by closeracing »

What controllers are compatible with this software?
futrelis
Posts: 14
Joined: Sat Jul 22, 2017 12:56 am

Re: Poor quality photo engraving

Post by futrelis »

linuxcnc is a controller like wincnc but it is free.
You only need to pay a mesa fpga card for about 100usd
http://mesaus.com/


Another chinese controller i know is trocen anywells that costs about 300usd but i think is similar to ruida
https://www.sign-in-china.com/products/ ... ystem.html
closeracing
Posts: 22
Joined: Sat Jul 08, 2017 1:38 am

Re: Poor quality photo engraving

Post by closeracing »

So to be clear, it is plug and play with a laser using a Ruida controller
futrelis
Posts: 14
Joined: Sat Jul 22, 2017 12:56 am

Re: Poor quality photo engraving

Post by futrelis »

linuxcnc is not plug and play.

awc708c is a controller like ruida is to some degree plug and play if you know how to install it
works like ruida but i don't know what quality engraving it has..
Last edited by futrelis on Sun Jul 23, 2017 6:33 pm, edited 1 time in total.
closeracing
Posts: 22
Joined: Sat Jul 08, 2017 1:38 am

Re: Poor quality photo engraving

Post by closeracing »

Ok got it. Are there wiring schematics available?
futrelis
Posts: 14
Joined: Sat Jul 22, 2017 12:56 am

Re: Poor quality photo engraving

Post by futrelis »

yes there are wiring schematics and tutorials on youtube like this https://www.youtube.com/watch?v=zn2iAqhyxBg
closeracing
Posts: 22
Joined: Sat Jul 08, 2017 1:38 am

Re: Poor quality photo engraving

Post by closeracing »

Thank you for all the information. I'll definitely check it out.
I have to have very high-quality engravings as I bought this laser for a monument business. I will let you know what happens with the tube, and in the meantime, I am going to try your photograv settings.
closeracing
Posts: 22
Joined: Sat Jul 08, 2017 1:38 am

Re: Poor quality photo engraving

Post by closeracing »

This is an engraving at 57% power, photograv interactive mode and adjust ed density to 0
histogram black to 0 white to 255 and gamma to 1. 300DPI and interval set to 0.0847.
Attachments
FullSizeRender (6).jpg
FullSizeRender (6).jpg (105.5 KiB) Viewed 5064 times
closeracing
Posts: 22
Joined: Sat Jul 08, 2017 1:38 am

Re: Poor quality photo engraving

Post by closeracing »

This engraving was done with photograv settings ed density to 0
histogram black to 0 white to 255 and gamma to 1. 300 DPI 57% power 300 mm sec and interval set to 0.0847.
It seems the quality is getting worse even with these proven settings
Post Reply