Settings for HR photo engraving

We provide online after sales support here, very quick reply.

Moderators: baker, Thunder laser - Tom, Thunder Laser -Nolan

Forum rules
All members should make themselves familiar with the forum rules. Please ensure you read this section of the forum BEFORE posting.
This sub-forum is only for thunderlaser users ask for tech support from thunderlaser tech persons directly. The normal member should raise your questions in the General Discussion sub-forum. Before ask a new question, please read the "Previously Asked Questions"first to save your time.
Post Reply
User avatar
woodcraf
Posts: 12
Joined: Fri Jun 17, 2016 8:31 am

Settings for HR photo engraving

Post by woodcraf »

Hi there - can you please confirm what size lens to use with the HR laser head? Is it the same 2" (50.8mm) lens that is used with the standard head or something else?

Also - can you provide suggested settings (power, speed, and interval) for achieving good results with the HR head on wood?

Thanks!
Ben
Posts: 137
Joined: Tue May 24, 2016 9:06 am

Re: Settings for HR photo engraving

Post by Ben »

Good day!

Yes,the HR laser head is used with 2'' lens that is used with the standard head,but there're two 2 " lens are installed inside.

For the HR photo engraving,you should find a high resolution image or picture first.
How to set the picture on the software,please go to below link.
http://www.thunderlaser.com/laser-engra ... mages.html
http://www.thunderlaser.com/laser-engra ... tting.html
http://www.thunderlaser.com/laser-engra ... nting.html

And the setting(power, speed, and interval) ,i will suggest the power 15% to 25% (according to the laser tube),speed 500mm/s and interval 0.06(DPI 400 ).

Hope it can help for your work.

By the way,please improve your profile for machine info so we can check your machine information.
viewtopic.php?f=6&t=13530
User avatar
woodcraf
Posts: 12
Joined: Fri Jun 17, 2016 8:31 am

Re: Settings for HR photo engraving

Post by woodcraf »

Thank you for your response.

Can you please show how the two lenses are to be installed in the HR laser head? Are they stacked on top of each other? This is not clear to me - thank you.

I have a Nova 35 130w - I could not find where to add my machine's serial number to my profile.

Thank you - Dan
Ben
Posts: 137
Joined: Tue May 24, 2016 9:06 am

Re: Settings for HR photo engraving

Post by Ben »

Good day!

Sorry for my late reply,just back from the Lantern Festival.

For the lenses in the HR laser head,you can take out them to check and the direction of installation for two focus lenses please refer to below picture.
123.png
123.png (17.77 KiB) Viewed 8054 times
About the problem from the profile,i will check and tell you later.
User avatar
woodcraf
Posts: 12
Joined: Fri Jun 17, 2016 8:31 am

Re: Settings for HR photo engraving

Post by woodcraf »

Hi Ben - thank you. That is how I have the one lens installed (it is facing the correct way).

My original question still stands - how do you install two lenses? Do you stack them on top of each other?

Thanks
Ben
Posts: 137
Joined: Tue May 24, 2016 9:06 am

Re: Settings for HR photo engraving

Post by Ben »

Good day!

They are stacked with two fixing rings.see below.
HR1.jpg
HR1.jpg (269.97 KiB) Viewed 7345 times
HR2.jpg
HR2.jpg (260.61 KiB) Viewed 7345 times
HR3.jpg
HR3.jpg (228.76 KiB) Viewed 7345 times
User avatar
woodcraf
Posts: 12
Joined: Fri Jun 17, 2016 8:31 am

Re: Settings for HR photo engraving

Post by woodcraf »

Excellent - thank you!
Post Reply