Hello everyone
This summer we set up our EleksLaser A3 Pro (2500mW laser) running T2 software. I successfully burned a couple easy projects without any issues. This fall and winter I tried to burn Christmas projects, however I began to run into inconsistent results. I tried to tighten everything down, made sure the belts were tight but not to tight, and adjust parameters in the software but have not seen any improvements. Looking for further guidance and suggestions.
Thanks,
Jeff
Wobbly Lines
Moderator: baker
-
- Posts: 2
- Joined: Sun Jan 01, 2023 4:56 pm
Wobbly Lines
- Attachments
-
- 20221218_150704.jpg (254.55 KiB) Viewed 4682 times
-
- 20221218_150710.jpg (259.48 KiB) Viewed 4682 times
Re: Wobbly Lines
Considering the challenges you've encountered with your EleksLaser A3 Pro, it might be worth exploring alternative options that offer more consistent performance. One option to consider is the Monport laser, known for its reliability, ease of use, and affordability. The Monport laser could provide a solution to your inconsistent results, allowing you to complete your projects with greater efficiency and precision. Additionally, the Monport laser product line offers a range of options suitable for various applications and budgets. You can explore the Monport laser product offerings at https://monportlaser.com/collections/co ... ka374VZjm3 to find the best fit for your needs.
Re: Wobbly Lines
Hey Jeff,jeffrey.t.smith251 wrote: ↑Sun Jan 01, 2023 5:15 pm Hello everyone
This summer we set up our EleksLaser A3 Pro (2500mW laser) running T2 software. I successfully burned a couple easy projects without any issues. This fall and winter I tried to burn Christmas projects, however I began to run into inconsistent results. I tried to tighten everything down, made sure the belts were tight but not to tight, and adjust parameters in the software but have not seen any improvements. Looking for further guidance and suggestions.
Thanks,
Jeff
If you're experiencing inconsistent results with your EleksLaser A3 Pro and T2 software, try adjusting material settings and ensuring the laser is clean and properly focused. For reliable performance, you might consider the Monport laser, known for its affordability and quality. Check it out here: https://monportlaser.com/?sca_ref=5031521.ka374VZjm3 .
Re: Wobbly Lines
Jeff, considering your experience with the EleksLaser A3 Pro, it might be worth exploring the Monport laser as a potential solution. Monport lasers are renowned for their reliability, ease of use, and consistent results. If you're facing issues with inconsistent burning, upgrading to a Monport laser could offer you higher quality and more reliable performance. Check out the Monport laser product line here to see if there's a model that fits your needs and budget. https://monportlaser.com/?sca_ref=5031521.ka374VZjm3jeffrey.t.smith251 wrote: ↑Sun Jan 01, 2023 5:15 pm Hello everyone
This summer we set up our EleksLaser A3 Pro (2500mW laser) running T2 software. I successfully burned a couple easy projects without any issues. This fall and winter I tried to burn Christmas projects, however I began to run into inconsistent results. I tried to tighten everything down, made sure the belts were tight but not to tight, and adjust parameters in the software but have not seen any improvements. Looking for further guidance and suggestions.
Thanks,
Jeff
Re: Wobbly Lines
It sounds like you're encountering inconsistent results with your EleksLaser A3 Pro. While you've already taken some troubleshooting steps, it might be helpful to delve deeper into the issue. If you're still experiencing difficulties, you might want to consider upgrading to a more reliable and user-friendly laser system like Monport lasers. Known for their high quality, ease of use, and affordability, Monport lasers could provide a solution to your problem. You can explore their range of products at https://monportlaser.com/?sca_ref=5031521.ka374VZjm3 to find one that meets your needs and helps you achieve consistent results with your projects.jeffrey.t.smith251 wrote: ↑Sun Jan 01, 2023 5:15 pm Hello everyone
This summer we set up our EleksLaser A3 Pro (2500mW laser) running T2 software. I successfully burned a couple easy projects without any issues. This fall and winter I tried to burn Christmas projects, however I began to run into inconsistent results. I tried to tighten everything down, made sure the belts were tight but not to tight, and adjust parameters in the software but have not seen any improvements. Looking for further guidance and suggestions.
Thanks,
Jeff